Autor Thema: blade 1000 startup PLZ help  (Gelesen 2908 mal)

Offline Freud-Schiller

  • Sobl Guru
  • *****
  • Beiträge: 927
blade 1000 startup PLZ help
« am: 03. September 2007, 15:48:31 »
Hi Leute, ich habe ein Thema auf einer Balde 1000. Das System ist mit einer 36GB Fiber Platte ausgerüsten und

ein Probe-scsi-all zeigt:

ok probe-scsi-all
/pci@8,600000/SUNW,qlc@4
LiD HA LUN  --- Port WWN ---  ----- Disk description -----
 1   1   0  2100000c50ac395a  SEAGATE ST336605FSUN36G A638

/pci@8,700000/scsi@6,1

/pci@8,700000/scsi@6
Target 6
  Unit 0   Removable Read Only device    TOSHIBA DVD-ROM SD-M14011009

Nach erfolgreicher Solaris installation bekomme ich aber folgendes:


The following disk configuration condition(s) have been
detected. Errors must be fixed to ensure a successful
installation. Warnings can be ignored without causing the
installation to fail.

WARNING: CHANGING DEFAULT BOOT DEVICE
You have either explicitly changed the default boot device, or
accepted the default to "Reconfigure EEPROM". In either case,
the system's EEPROM will be changed so it will always boot
Solaris from the device that you've specified. If this is not
what you had in mind, go back to the disk selection screens and
change the "Reconfigure EEPROM" setting.--------------------------------------------------------------------------------
     Esc-2_OK    Esc-5_Cancel     Esc-2_OK    Esc-5_Cancel
Preparing system for Solaris install

Configuring disk (c1t1d0)
        - Creating Solaris disk label (VTOC)

Creating and checking UFS file systems
        - Creating / (c1t1d0s0)

SUNW,Sun-Blade-1000 (UltraSPARC-III) , No Keyboard
Copyright 1998-2001 Sun Microsystems, Inc.  All rights reserved.
OpenBoot 4.2, 2048 MB memory installed, Serial #51383810.
Ethernet address 0:3:ba:10:e:2, Host ID: 83100e02.
                                                                      Boot device: disk  File and args:
The file just loaded does not appear to be executable.
ok boot disk
Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@1,0  File and args:
The file just loaded does not appear to be executable.



Ich verstehe das Thema nicht :( außderdem habe ich von Fiber Channel NULL Ahnung, noch weniger als sonst :D Kann mir da wer helfen? Viele grüße David

sonnenblen.de - Das unabhängige Sun User Forum

blade 1000 startup PLZ help
« am: 03. September 2007, 15:48:31 »

Offline escimo

  • Sobl Moderator
  • Sobl Guru
  • *****
  • Beiträge: 1674
  • SPARCstation 2
    • Youtube-Kanal opensparcbox.org
Re: blade 1000 startup PLZ help
« Antwort #1 am: 03. September 2007, 18:13:04 »
Hi David,

hast du die Platte tauschen müssen?

Jede FC-Platte besitzt eine einzigartige WWN (world wide number) zur Identifikation. Damit du vom OBP von der neuen Platte booten kannst, ist es eventuell erforderlich den HW-Pfad mit der gültigen WWN anzupassen.

Ich habe bei sunsolve oder sunshack damals gelesen, wie man beim Tausch von FC-Platten bei eine Blade 1000 vorgehen muss.

Ob das aber zu deinem Problem passt, kann ich nicht ganz feststellen.

Gruß
Stephan

Offline escimo

  • Sobl Moderator
  • Sobl Guru
  • *****
  • Beiträge: 1674
  • SPARCstation 2
    • Youtube-Kanal opensparcbox.org
Re: blade 1000 startup PLZ help
« Antwort #2 am: 03. September 2007, 18:31:44 »
Da hab ich einige Sachen gefunden:

[1.]
Seagate ST336605FC 36GB and ST373405FC 73G drives could be susceptible to label corruption. (FIN I0816-1)

Du hast eine Seagate ST336605FC 36GB Platte installiert. Dazu gibt es eine FIN (field information notice). Aber das passt nicht richtig zu deinem Problem.

[2.]
Error installing Solaris on ST318304 FC-AL disk drives: Could not create Solaris disk label (VTOC) (SRDB 24407).

[3.]
Recovering from a failed FCAL boot disk. (SRDB 17643)

[4.]
Correcting device paths when replacing fiber boot disks after a ufsrestore. (Infodoc 40133)

Das hier könnte es sein!  :-\
Unter sunsolve auf Systembeschreibung Blade 1000, Repair Procedures, Component: Disk Drive

Gruß
Stephan

PS: Du hast eine PM ;)

Offline AndreasW

  • Sobl Master
  • ****
  • Beiträge: 254
Re: blade 1000 startup PLZ help
« Antwort #3 am: 03. September 2007, 20:02:33 »
Hallo Freud-Schiller,

falls die bisherigen Antworten Deine Fragen noch nicht beantworten konnten, schreib doch noch ein wenig über den Kontext:
- handelt es sich um eine Neuinstallation, Upgrade  oder ein Laufwerkstausch mit anschließendem Restore eines Backups?
- welche OBP-Version hat die Maschine?

Soweit ich Dich verstanden habe, kommt die irritierende Meldung nach dem Abschluss der Installation.
Es ist völlig normal, dass die Installation den Parameter boot-device verändert. Ich habe es aber noch nicht
erlebt, dass es vorher eine Warnung darüber gab. Die nachfolgende Meldung über das Schreiben einer neuen
vtoc ist mir so auch noch nicht untergekommen, aber auch zu verstehen, wenn Du zuvor dem Installationsprogramm
Deinen Wunsch nach neuer Aufteilung kund getan hast ;-)
Diese Meldung würde ich dann aber auch vor dem Übertragen der ausgewählten Software erwarten.

Gruß
Andreas